Refer to the exhibit. What could be possible causes for the “Serial0/0 is down” interface status?
A. A Layer 1 problem exists.
B. The bandwidth is set too low.
C. A protocol mismatch exists
D. An incorrect cable is being used.
E. There is an incorrect IP address on the Serial 0/0 interface.
Before installing a new, upgraded version of the IOS, what should be checked on the router, and
which command should be used to gather this information? (Choose two.)
A. the amount of available ROM
B. the amount of available flash and RAM memory
C. the version of the bootstrap software present on the router
D. show version
E. show processes
F. show running-config
Refer to the exhibit. Which two statements are true about interVLAN routing in the topology that is
shown in the exhibit? (Choose two.)
A. Host E and host F use the same IP gateway address.
B. Router1 and Switch2 should be connected via a crossover cable.
C. Router1 will not play a role in communications between host A and host D.
D. The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.
E. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.
F. The FastEthernet 0/0 interface on Router1 and Switch2 trunk ports must be configured using
the same encapsulation type.
Refer to the exhibit. Which two statements are true about the loopback address that is configured
on RouterB? (Choose two.)
A. It ensures that data will be forwarded by RouterB.
B. It provides stability for the OSPF process on RouterB.
C. It specifies that the router ID for RouterB should be 10.0.0.1.
D. It decreases the metric for routes that are advertised from RouterB.
E. It indicates that RouterB should be elected the DR for the LAN.
If you are a network administrator, how will you explain VTP configuration to a new technician?
A. In the VTP client mode, a switch is unable to update its local VLAN database.
B. Configure a trunk link between the switches to forward VTP updates.
C. In the VTP server mode, a switch is able to update a switch in the VTP transparent mode.
D. In the VTP transparent mode, a switch will forward the received updates to other switches.
E. A switch in the VTP server mode only updates switches in the VTP client mode that have a
higher VTP revision number.
F. A switch in the VTP server mode will update switches in the VTP client mode regardless of the
configured VTP domain membership.
VTP operates in one of three modes:
Server – In this VTP mode you can create, remove, and modify VLANs. You can also set other
configuration options like the VTP version and also turn on/off VTP pruning for the entire VTP
domain. VTP servers advertise their VLAN configuration to other switches in the same VTP
domain and synchronize their VLAN configuration with other switches based on messages
received over trunk links. VTP server is the default mode. The VLANs information are stored on
NVRAM and they are not lost after a reboot.
Client – VTP clients behave the same way as VTP servers, but you cannot create, change, or
delete VLANs on the local device. In VTP client mode, VLAN configurations are not saved in
Cisco IOS (originally Internetwork Operating System) is the software used on the vast majority of
Cisco Systems routers and all current Cisco network switches. Which two of the following devices
could you configure as a source for the IOS image in the boot system command? (Choose two.)
C. flash memory
D. HTTP server
E. TFTP server
F. Telnet server
What are two reasons a network administrator would use CDP? (Choose two.)
A. to obtain VLAN information from directly connected switches
B. to determine the status of network services on a remote device
C. to determine the status of the routing protocols between directly connected routers
D. to verify the type of cable interconnecting two devices
E. to verify Layer 2 connectivity between two devices when Layer 3 fails
F. to obtain the IP address of a connected device in order to telnet to the device
Cisco Discovery Protocol (CDP) is primarily used to obtain protocol addresses of neighboring
devices and discover the platform of those devices. CDP can also be used to show information
about the interfaces your router uses. CDP is an independent media protocol and runs on all
Cisco-manufactured devices including routers, bridges, access servers, and switches. It should be
noted that CDP is a protocol which works on the layer2. By default, multicast advertise is sent
every 60 seconds to 01-00-0 c-cc-cc-cc as the destination address . When reaching the holdtime
of 180 seconds , if not receiving the advertise from neighboring devices yet, the information of
neighboring devices will be cleared.
Cisco Discovery Protocol (CDP) is a proprietary protocol designed by Cisco to help administrators
collect information about both locally attached and remote devices. By using CDP, you can gather
hardware and protocol information about neighbor devices, which is useful info for troubleshooting
and documenting the network.
You can use:
Show cdp neighbor
Show cdp neighbor details
Commands to gather the information of connected neighbors.
Refer to the exhibit. Both switches are using a default configuration. Which two destination
addresses will host 4 use to send data to host 1? (Choose two.)
A. the IP address of host 1
B. the IP address of host 4
C. the MAC address of host 1
D. the MAC address of host 4
E. the MAC address of the Fa0/0 interface of the R1 router
F. the MAC address of the Fa0/1 interface of the R1 router
Refer to the exhibit. The router has been configured with these commands:
What are the two results of this configuration? (Choose two.)
A. The default route should have a next hop address of 184.108.40.206.
B. Hosts on the LAN that is connected to FastEthernet 0/1 are using public IP addressing.
C. The address of the subnet segment with the WWW server will support seven more servers.
D. The addressing scheme allows users on the Internet to access the WWW server.
E. Hosts on the LAN that is connected to FastEthernet 0/1 will not be able to access the Internet
without address translation.
Since the hosts on the Fast Ethernet 0/1 network are using private RFC 1918 IP addressing
(192.168.10.0/24) their IP addresses will need to be translated into a publicly routable address in
order to access the Internet. However, the server is using the 220.127.116.11 IP address, which is
publicly routable and so Internet users can indeed access this server (assuming that the
18.104.22.168 IP address has been correctly assigned to the network)
Your Company has installed IP phones. Both the phones and the office computers connect to the
same device. The phone traffic and the office computer data traffic must be on different networks
to ensure maximum throughput for the phone data. Which network device can be best connected
to the phones and computers, and which technology will be performed on this device? (Choose
You can configure VLANs on the switch to distinguish two types of data traffic.